Security Link SL150 Průvodce řešením problémů Strana 51
- Strana / 144
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Section 8 - 4285/4286 VIP Phone Module
8–3
4285/4286 VIP MODULE WIRING NOTES:
•
Wire the phone module exactly as shown, using a direct-connect cord and RJ31X jack.
•
If touch-tones are not heard when pressing
keys
following phone access to the security system via
an on-premises phone, try reversing the pair of wires connected to terminals 3 and 4 on either
phone module
and
the pair of
wires connected to terminals 21 and 22 on the control.
•
If an error signal (
fast
busy signal) is
heard
when trying to access the system via the phone, check
for correct line seizure wiring, as described in note 4.
•
Connection to
the
incoming telco line
via
an RJ31X jack and direct-connect cord, as shown in this
diagram, is essential, even if the system is not connected to a Central Station.
The 4285 or 4286
will not function if this is not done.
The house phone lines (gray and brown wires) must be wired to the phone module
terminals, not to the control terminals. Otherwise, an error signal
(fast busy signal)
will
occur when trying to access the system from an on-premises phone.
•
If the telephone
system
on the
premises
includes a Caller ID unit, connect the unit
directly
to the
Handset terminals (21 and 22) on the control, as shown below.
TERMINALS
ON CONTROL
TO EARTH GROUND (COLD WATER PIPE, ETC.)
SPEAKER VOLUME
ADJUSTABLE ON
4286 ONLY
UNUSED
KEYED
HEADER
4285/4286
VIP MODULE
123456 7
CONNECTOR
WITH FLYING
LEADS
TO CONTROL
PANEL
TERMINALS
USED FOR
KEYPAD
CONNECTIONS
PREMISES
ANSWERING
MACHINES
AND PHONES
TIP
RING
RJ31X
JACK
PLUG
TIP
RING
MUST CONNECT TO
ON 4285 (TIP)
MUST CONNECT TO
ON 4285 (RING)
GREEN (TIP)
RED (RING)
1
2
INCOMING TELCO LINE
GREY (R)
BROWN (T)
4285/4286
TERMINAL ASSIGNMENTS
1 - TIP
2 - RING
PHONE INPUT
3 - TIP
4 - RING
PHONE OUTPUT
5 - GROUND
6 -
7 -
AUDIO OUT (4286 ONLY)
IMPORTANT NOTE FOR
EXISTING INSTALLATIONS:
EXISTING WIRES
CONNECTED TO THE
"HANDSET" TERMINALS ON
CONTROL MUST BE MOVED
FROM THERE TO TERMINALS
3 AND 4 ON THE 4285.
*
*
*NOTE:
IF THE TELEPHONE
HAS BUILT-IN CALLER ID,
THE CALLER ID FUNCTION
MAY NOT WORK.
CA38A
IN
CANADA
DIRECT
CONNECT
CORD
HANDSET
GROUND
INCOMING
TELCO
LINE
IMPORTANT!
IF THE PANEL IS NOT CONNECTED TO A
PROPER EARTH GROUND, YOU MAY GET
FALSE TELEPHONE LINE CUT INDICATIONS
(IF THE TELEPHONE LINE MONITOR HAS
BEEN PROGRAMMED).
NO CONNECTION
YELLOW: TO DATA OUT (TERM. 7)
RED: TO AUX. (+) (TERM. 8)
BLACK: TO AUX. GROUND (-) (TERM. 4)
GREEN: TO DATA IN (TERM. 6)
22
21
23
24
25
CALLER ID
UNIT
ANSWERING
MACHINE
TO GND
TERMINAL (25)
ON CONTROL
Figure 19. 4285/4286 VIP Module Wiring Connections
- 6HF XULW\6\VWHP 1
- Table of Contents 4
- List of Figures 7
- Introduction 9
- FINAL POWER 12
- Installing the Control 13
- RCVR BRD 15
- TERMINALS 16
- ON CONTROL 16
- Wiring the AC Transformer 17
- Installing the Backup Battery 18
- Earth Ground Connections 18
- Installing Remote Keypads 19
- Mounting the Keypads 20
- AUX. DATA 21
- Basic Hardwired Zones 1–8 23
- Remote Keyswitch (Zone 7) 27
- Wired Zone Expansion 33
- Wireless Expansion 37
- 1 2 3 4 5 38
- Installing the 5800TM Module 39
- Jam Detection and Reporting 39
- Appendix A 42
- Powerline Carrier Devices 47
- Programming Relay Outputs 48
- 4285 & 4286 VIP Module 49
- Section 11: 50
- Audio Alarm 50
- Verification (AAV) Unit 50
- 4285/4286 51
- VIP MODULE 51
- External Sounders 53
- Sounder Connections and Power 54
- Sounder Supervision 54
- Testing the Sounder 54
- Long Range Radio 55
- Dynamic Signaling Feature 56
- 4285 or 4286 58
- Final Power-Up 59
- Battery Tests 60
- Mechanics of Programming 61
- Loading Factory Defaults 63
- Exiting the Programming Mode 63
- Data Field Descriptions 69
- OUTPUT TO LONG RANGE RADIO 74
- Allows 81
- Zone Programming 83
- 86
- To Remove a Zone 88
- Section 16 -Zone Programming 91
- Output Device Programming 93
- Zone Lists 99
- Alpha Descriptor Programming 101
- Adding Custom Words 103
- ALPHA VOCABULARY LIST 105
- CHARACTER (ASCII) CHART 105
- Macros (SpeedKey) 107
- Remote Programming and 109
- Control (Downloading) 109
- Remote Programming Commands 110
- Initial Download 110
- System Communication 111
- System Operation 115
- Keypad Functions 116
- Testing the System 121
- Troubleshooting Guide 123
- POSSIBLE CAUSE REMEDY 124
- SYMPTOM POSSIBLE 124
- CAUSE REMEDY 124
- CONTACTING TECHNICAL SUPPORT 125
- In This Section 127
- APPENDIX A 131
- Regulatory Agency Statements 133
- Warnings and Limitations 135
- DOC LOAD NO.: 3 143
- ¬19'l 144
- Two Mid America Plaza 144
- Suite 200 144
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Security Link SL150
(29 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce